|
|
| (5 intermediate revisions by 2 users not shown) |
| Line 1: |
Line 1: |
| − | ==Feedback module==
| + | #REDIRECT [[Category:Request moduls]] |
| | | | |
| − | ===General===
| |
| | | | |
| − | A feedback system can be equipped with the S88 bus. <br>
| |
| − | This S88 bus cabling must always be set up in a straight line. It can be connected up to 32 RM decoder consecutively. <br>
| |
| − | It can use the modules from different manufacturers. <br>
| |
| − | However is recommended if possible to stay with one brand. <br>
| |
| − | <br>
| |
| − | The planned [[DC-Car-XT]] can independently trigger reactions such as turn a junction. <br>
| |
| − | The IR LED can be installed on the vehicle :
| |
| − | * From the bottom of the vehicle [[sensor]] s can detect vehicles in a roadway lane.
| |
| − | * From the side of a vehicles in one lane.
| |
| − | * From the back, the signal can be deceted [[R%C3%BCckmeldesensoren#Leitpfosten | delineator posts]] with phototransistor.
| |
| − |
| |
| − | ===Feedback unit RMD ===
| |
| − | The [[S88 RMD]] is a feedback decoder with 16 connections available. <br>
| |
| − | By a switch or the wheels of a train, the inputs to ground can be switched and thus generate an occupation signal. <br>
| |
| − |
| |
| − | === Feedbacks S88 with optocouplers ===
| |
| − | The decoders are robust against false wiring. <br>
| |
| − | Module: [[S88 opto]]
| |
| − | Through the optical input [[optocouplers]] the circuits are separated. <br>
| |
| − | Such input needs some milliamps of current for switching and therefore can not be used with IR-sensors. <br>
| |
| − |
| |
| − | === Feedbacks S88 DC Car ===
| |
| − | Module: [[S88 DC Car 16]]
| |
| − | Only [[phototransistors]] should be used as the input has a electronic filter.
| |
| − | Such input needs some microamperes of current for switching and are thus sensitive if long leads are used. <br>
| |
| − |
| |
| − | === Feedback unit with SET/RESET ===
| |
| − | Through Set / Reset a permanent Busy message is generated <br>
| |
| − | Module: [[S88-CAR]]
| |
| − | To use with any software because the hardware stores the signal. <br>
| |
| − | Also available as [[S88 DC CAR8]] for connecting IR sensors.
| |
| − |
| |
| − | ===Feedbacks on time ===
| |
| − | A Busy message is extended in time, so that the equipment and software have time to process the message. <br>
| |
| − | Module: [[S88-2 sec]].
| |
| − | Since a reed contact or a Hall sensor only produces a very short pulse, the signal is extended to 2 seconds with this feedback decoder. <br>
| |
| − | That's enough for a model software that allows itself a saving of feedback.
| |
| − | Not suitable for IR feedback! <br>
| |
| − |
| |
| − | ==Sensoren==
| |
| − | Von der Straße muss die [[Rückmeldung]] erfasst werden.<br>
| |
| − | Dazu gibt es verschiedene Möglichkeiten.<br> Siehe [[Rückmeldesensoren]]<br>
| |
| − | <br>
| |
| − |
| |
| − |
| |
| − | [[Category:Index]]
| |
| | [[Category:DC-Car-System]] | | [[Category:DC-Car-System]] |
| | [[Category:Electronic]] | | [[Category:Electronic]] |
| − | [[Category:RMD]]
| |
| | [[Category:Software]] | | [[Category:Software]] |
| | [[Category:Windigipet]] | | [[Category:Windigipet]] |
| | + | [[Category:Index_US]] |
| | + | [[Category:Index_UK]] |
