Difference between revisions of "Inputprint"
m |
m |
||
Line 3: | Line 3: | ||
<br> | <br> | ||
==Switchboard for Servo- und traffic light decoder== | ==Switchboard for Servo- und traffic light decoder== | ||
− | The servo decoder from DC-Car (MoBa-Claus) can also be operated with a PC via the RS232 port. | + | The servo decoder from DC-Car (MoBa-Claus) can also be operated with a PC via the RS232 port.<br> |
Besides the progamm for the servo decoder, the CD also includes a program for operating the servos by mouse or keyboard.<br> | Besides the progamm for the servo decoder, the CD also includes a program for operating the servos by mouse or keyboard.<br> | ||
With self-written programs it is feasible to implement some time-automatic sequences.<br> | With self-written programs it is feasible to implement some time-automatic sequences.<br> | ||
Line 14: | Line 14: | ||
<br> | <br> | ||
<br> | <br> | ||
− | + | The Prozessor get the signals from switch, reedswitch, Hallsensors or IR-Sensoren from (MINUS) and take it over RS232-chip to the connetion from the Servodecoder.<br> | |
<br> | <br> | ||
<br> | <br> | ||
− | |||
− | |||
<br> | <br> | ||
+ | The positions off the servos are controlled with the programmer over the PC. <br> | ||
<br> | <br> | ||
− | |||
<br> | <br> | ||
<br> | <br> | ||
Line 30: | Line 28: | ||
==Anschluss== | ==Anschluss== | ||
− | === | + | ===Controlled Servodecoders S4 and S8=== |
[[File:S_Vorsatz_Bestueckung_neu.png|350px]]<br> | [[File:S_Vorsatz_Bestueckung_neu.png|350px]]<br> | ||
− | === | + | ===Controlled Servodecoder W4=== |
[[File:S_Vorsatz_W4.png|350px]]<br> | [[File:S_Vorsatz_W4.png|350px]]<br> | ||
− | === | + | ===Controlled Ampeldecoder=== |
[[File:Schaltervorsatz_Ampel.png|350px]]<br> | [[File:Schaltervorsatz_Ampel.png|350px]]<br> | ||
<table Border="1"> | <table Border="1"> | ||
Line 43: | Line 41: | ||
<tr> | <tr> | ||
− | <td>+ 5 V Out</td><td>- | + | <td>+ 5 V Out</td><td>- Ground</td><td>Trafficlight A - D</td><td>Call Light</td><td>Night</td><td>Nothalt</td><td>Start B</td><td>Start A</td><td>auto, off</td><td>auto. off</td> |
</tr> | </tr> | ||
<tr> | <tr> | ||
− | <td> </td><td> </td><td> | + | <td> </td><td> </td><td> green red</td><td> </td><td> </td><td> </td><td> </td><td> </td><td> </td><td> </td> |
</tr> | </tr> | ||
</table> | </table> | ||
<br><br><br><br><br><br><br> | <br><br><br><br><br><br><br> | ||
− | == | + | ==Kitmanual== |
− | siehe [[ | + | siehe [[Kit contruction inputprint]] |
− | [[Servodecoder]] [[ | + | [[Servodecoder]] [[Trafficlightdecoder]]<br> |
− | == | + | ==Ation== |
− | + | Hallsensors and R-Sensoren need a +5V connetion.<br> | |
+ | The left connector is 5V <br> | ||
<br> | <br> | ||
− | ''' | + | '''use the servodecoder:''' with Extanionsconnector<br> |
<table border=1> | <table border=1> | ||
<tr><td> | <tr><td> | ||
Line 66: | Line 65: | ||
1. [[File:S8-W4.png|180px|Bild S8-W4.png]] 2. [[File:Master_Bruecke.png|180px|Bild Master_Bruecke.jpg]]<br> | 1. [[File:S8-W4.png|180px|Bild S8-W4.png]] 2. [[File:Master_Bruecke.png|180px|Bild Master_Bruecke.jpg]]<br> | ||
<br> | <br> | ||
− | |||
− | |||
<br> | <br> | ||
− | [[File:S8undHS_zusammengesteckt.jpg|250px| | + | [[File:S8undHS_zusammengesteckt.jpg|250px|S8 and IP together]]<br> |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
− | + | ||
<br> | <br> | ||
+ | One screw is removed from the plug and the socket.<br | ||
+ | Then the assemblies can be plugged together and the ground connection is still given | ||
+ | If the switch is installed in a switchboard for the pushbuttons, a standard RS232 extension cable can be used | ||
<br><br><br> | <br><br><br> | ||
==Weichenstrasse== | ==Weichenstrasse== | ||
− | [[File:weichenstrasse.png|450px | + | [[File:weichenstrasse.png|450px]]<br> |
− | + | One switch can be used to operate several points simultaneously<br> | |
− | + | The resistances should be 4.7 K and the diodes should be 1N4148<br> | |
− | + | A control unit can be equipped with an RS232 cable (9-pin sub-D extension) <br> | |
− | + | remote from the servo decoder.<br> | |
− | + | ||
− | + | ||
− | + | ||
− | + | ||
[[Servodecoder]] <br> [[:category:Traffic_signal_decoder|Traffic_signal_decoder]]<br><br> | [[Servodecoder]] <br> [[:category:Traffic_signal_decoder|Traffic_signal_decoder]]<br><br> |
Revision as of 21:05, 27 October 2017
Contents
Anwendung DE
Switchboard for Servo- und traffic light decoder
The servo decoder from DC-Car (MoBa-Claus) can also be operated with a PC via the RS232 port.
Besides the progamm for the servo decoder, the CD also includes a program for operating the servos by mouse or keyboard.
With self-written programs it is feasible to implement some time-automatic sequences.
As another option for connecting to this interface is the so called switchboard.
The Prozessor get the signals from switch, reedswitch, Hallsensors or IR-Sensoren from (MINUS) and take it over RS232-chip to the connetion from the Servodecoder.
The positions off the servos are controlled with the programmer over the PC.
Anschluss
Controlled Servodecoders S4 and S8
Controlled Servodecoder W4
Controlled Ampeldecoder
1 | 2 | 3-10 | 11+12 | 13 | 14 | 15 | 16 | 17 | 18 |
+ 5 V Out | - Ground | Trafficlight A - D | Call Light | Night | Nothalt | Start B | Start A | auto, off | auto. off |
green red |
Kitmanual
siehe Kit contruction inputprint
Servodecoder Trafficlightdecoder
Ation
Hallsensors and R-Sensoren need a +5V connetion.
The left connector is 5V
use the servodecoder: with Extanionsconnector
S8DCC/MOT ab 02.01.09 | W4DCC/MOT ab 26.04.09 | |
S4DCC/MOT ab 21.10.08 | Ampeldecoder ab 10.10 |
One screw is removed from the plug and the socket.<br
Then the assemblies can be plugged together and the ground connection is still given
If the switch is installed in a switchboard for the pushbuttons, a standard RS232 extension cable can be used
Weichenstrasse
One switch can be used to operate several points simultaneously
The resistances should be 4.7 K and the diodes should be 1N4148
A control unit can be equipped with an RS232 cable (9-pin sub-D extension)
remote from the servo decoder.