Difference between revisions of "XT-Modul-battery test"
(→Values for the car decoder) |
|||
| Line 21: | Line 21: | ||
[[CV25]] = 1 Transmitting from the back (via the IR LEDs for distance control) or <br> | [[CV25]] = 1 Transmitting from the back (via the IR LEDs for distance control) or <br> | ||
[[CV25]] = 4 Side or bottom transmitter <br> | [[CV25]] = 4 Side or bottom transmitter <br> | ||
| − | [[CV26]] | + | [[CV26]] Function of the vehicle with battery empty <br> |
[[CV27]] = 2 or 10 battery test turned on <br> | [[CV27]] = 2 or 10 battery test turned on <br> | ||
[[CV28]] = 50 (1.2V) or 100 (2.4V) or 130 (3.6V battery) <br> | [[CV28]] = 50 (1.2V) or 100 (2.4V) or 130 (3.6V battery) <br> | ||
| Line 45: | Line 45: | ||
For direct control of a servo on the XT module. | For direct control of a servo on the XT module. | ||
Please pay attention to the correct connection sequence, as these might vary with the different manufacturers. <br> | Please pay attention to the correct connection sequence, as these might vary with the different manufacturers. <br> | ||
| − | * | + | * IR-LED Connetor (with out resistend) <br> |
To send one command to the DC-Car<br> | To send one command to the DC-Car<br> | ||
<br> | <br> | ||
| − | Left [[ | + | Left [[Category:Function_moduls,_Function_decoders | Function_decoder]] right [[XT-Modul]] |
The Xt-Modul send one command, indecator right, and the Servo go to right for a few sekunds.<br> | The Xt-Modul send one command, indecator right, and the Servo go to right for a few sekunds.<br> | ||
[[File:XT-Akku.png]]<br> | [[File:XT-Akku.png]]<br> | ||
| Line 54: | Line 54: | ||
=== Setting XT module === | === Setting XT module === | ||
| + | |||
| + | |||
| + | CV for Vehicle [[DC-Car_battery_check]]<br> | ||
[https://miniatuura.nl/wp-content/uploads/2022/03/XT-module-with-low-battery-te...pdf XT-module-with-low-battery-te...pdf]<br> | [https://miniatuura.nl/wp-content/uploads/2022/03/XT-module-with-low-battery-te...pdf XT-module-with-low-battery-te...pdf]<br> | ||
| − | + | ||
[[Category:Index_DE]] | [[Category:Index_DE]] | ||
Latest revision as of 20:56, 3 September 2023
Contents
Basics DC-Car-XT
When it is set to: Evaluation of the battery test
- Sorting out vehicles with an empty battery to reach a charging station (in conjunction with software fully automatic charging is possible).
Other options: see XT-Module
Infrared transmit and receive
As sensor we require a photo transistor.
It can be installed:
- In the delineators post
- In the street as manhole cover
- As a sensor in a stationary vehicle
- hiding in trees, shrubs, buildings,...
Values for the car decoder
CV25 = 1 Transmitting from the back (via the IR LEDs for distance control) or
CV25 = 4 Side or bottom transmitter
CV26 Function of the vehicle with battery empty
CV27 = 2 or 10 battery test turned on
CV28 = 50 (1.2V) or 100 (2.4V) or 130 (3.6V battery)
DC-Car-XT-Modul
- Switching a 3-way servo turn out
- Switching a contact to ground / GND
- Transmitting a freely selectable DC Car Infrared command
You can choose whether the respective function is resetted after a certain time or by triggering a reed contact.
Pin assignment
Connection Description
DC voltage of 5V / 500mA via screw terminal block or the mini USB port.
- LED indicator
Green LED: 5V operating voltage available. Blue LED: received valid signal.
- Photo transistor (+ and -)
Note: Reverse marked as an LED.
- Servo connection
For direct control of a servo on the XT module.
Please pay attention to the correct connection sequence, as these might vary with the different manufacturers.
- IR-LED Connetor (with out resistend)
To send one command to the DC-Car
Left right XT-Modul
The Xt-Modul send one command, indecator right, and the Servo go to right for a few sekunds.
Setting XT module
CV for Vehicle DC-Car_battery_check
XT-module-with-low-battery-te...pdf
