Difference between revisions of "XT-Modul-Accutest"
m |
m |
||
| Line 7: | Line 7: | ||
Other options: see '''[[XT Modul]]''' | Other options: see '''[[XT Modul]]''' | ||
[[File: xt_dc07.png | 230px | right | thumb | Side or bottom transmiter: DC07 needs a 100 ohms resistance]] | [[File: xt_dc07.png | 230px | right | thumb | Side or bottom transmiter: DC07 needs a 100 ohms resistance]] | ||
| − | |||
| − | |||
<br> | <br> | ||
==Infrared transmit and receive== | ==Infrared transmit and receive== | ||
| − | The sensor requires a | + | The sensor requires a photo transistor. <br> |
It can be installed: <br> | It can be installed: <br> | ||
* In the guidepost | * In the guidepost | ||
| Line 28: | Line 26: | ||
==DC-Car-XT-Modul== | ==DC-Car-XT-Modul== | ||
| − | [[File:xt_leitpfosten.png|230px|thumb| | + | [[File:xt_leitpfosten.png|230px|thumb|Delineator post with FTR]] |
| − | [[File:Xt sende ir1.png|230px|thumb| | + | [[File:Xt sende ir1.png|230px|thumb|Position of side transmitter]] |
#Switching a 3-way servo turn out <br> | #Switching a 3-way servo turn out <br> | ||
# Switching a contact to ground / GND <br> | # Switching a contact to ground / GND <br> | ||
| Line 36: | Line 34: | ||
You can choose whether the respective function is resetted after a certain time or by triggering a reed contact. <br> | You can choose whether the respective function is resetted after a certain time or by triggering a reed contact. <br> | ||
=== Pin assignment === | === Pin assignment === | ||
| − | [[File:xt_anschluss.png|400px| | + | [[File:xt_anschluss.png|400px|Connection of XT-Module]] |
=== Connection Description === | === Connection Description === | ||
DC voltage of 5V / 500mA via screw terminal block or the mini USB port. <br> | DC voltage of 5V / 500mA via screw terminal block or the mini USB port. <br> | ||
* '''LED indicator''' <br> | * '''LED indicator''' <br> | ||
Green LED: 5V operating voltage available. Blue LED: received valid signal. <br> | Green LED: 5V operating voltage available. Blue LED: received valid signal. <br> | ||
| − | * ''' | + | * '''Photo transistor (+ and -)''' <br> |
Note: Reverse marked as an LED. <br> | Note: Reverse marked as an LED. <br> | ||
* '''Servo connection''' <br> | * '''Servo connection''' <br> | ||
Revision as of 21:03, 20 November 2017
Contents
Basics DC-Car-XT
Default: Evaluation of the battery test
- Sorting out vehicles with an empty battery to reach a charging station, in conjunction with software fully automatic charging is possible)
Other options: see XT Modul
Infrared transmit and receive
The sensor requires a photo transistor.
It can be installed:
- In the guidepost
- In the street as manhole cover
- As a sensor in a stationary vehicle
- hiding in trees, shrubs, buildings
Values for the car decoder
CV25 = 1 Transmitting from the back (infrared LEDs of the rear distance control)
or CV25 = 4 Side or bottom transmitter
CV26 Function of the vehicle with battery empty
CV27 = 2 or 10 battery test turned on
CV28 = 50 (1.2V) or 100 (2.4V) or 130 (3.6V battery)
DC-Car-XT-Modul
- Switching a 3-way servo turn out
- Switching a contact to ground / GND
- Transmitting a freely selectable DC Car Infrared command
You can choose whether the respective function is resetted after a certain time or by triggering a reed contact.
Pin assignment
Connection Description
DC voltage of 5V / 500mA via screw terminal block or the mini USB port.
- LED indicator
Green LED: 5V operating voltage available. Blue LED: received valid signal.
- Photo transistor (+ and -)
Note: Reverse marked as an LED.
- Servo connection
For direct control of a servo on the XT module.
Please pay attention to the correct connection sequence, as these might vary with the different manufacturers.
Setting XT module
...
