Difference between revisions of "VT"
m (→Priorität rules VT VTL) |
m (→VT-TINY VTL-Tiny) |
||
| Line 9: | Line 9: | ||
* Parking stop / bus stop <br> | * Parking stop / bus stop <br> | ||
* Priority control left turn [[VTL]] | * Priority control left turn [[VTL]] | ||
| − | The | + | The priority tiny can be used with DC-Car to control the traffic. <br> |
| − | If a vehicle drives over a sensor (reed switch, Hall sensor HG1, IR sensor), an IR stop signal is generated for an adjustable time. | + | If a vehicle drives over a sensor (reed switch, Hall sensor HG1, IR sensor), an IR stop signal is generated for an adjustable time. |
| − | '' 'The stop signal of the VTL only reacts to vehicles with the left turn signal switched on.' '' <br> | + | '''The stop signal of the VTL tiny only reacts to vehicles with the left turn signal switched on.''' <br> |
| Line 19: | Line 19: | ||
'''to use with für 5 Volt'''<br> | '''to use with für 5 Volt'''<br> | ||
IC2 = VT Tiny<br> | IC2 = VT Tiny<br> | ||
| − | C1 + C5 = | + | C1 + C5 = Tantal capacitor 4,7uF/16 Volt<br> |
| − | C3 + C4 = | + | C3 + C4 = Tantal capacitor 1uF/16 Volt<br> |
| − | R1 = | + | R1 = Resistor for IR-LED 150 - 680 Ohm<br> |
| − | R2 = | + | R2 = Resistor 50K<br> |
| − | R4 = | + | R4 = Resistor 270 Ohm<br> |
| − | R6 = | + | R6 = Resistor 100 Ohm soldering vrticaly<br> |
| − | R7 = | + | R7 = Resistor 10K<br> |
</td><td> | </td><td> | ||
| − | ''' | + | '''expansion for 12 V'''<br> |
D1 = 1N4001 Diode<br> | D1 = 1N4001 Diode<br> | ||
| − | IC1 = 78S05 | + | IC1 = 78S05 Voltage regulator<br> |
| − | C2 = | + | C2 = Capacitor 470uF / 35 Volt<br> |
'''Parts:'''<br> | '''Parts:'''<br> | ||
8 pin 2,54mm<br> | 8 pin 2,54mm<br> | ||
4 pin for power<br> | 4 pin for power<br> | ||
[[IR-LED]]<br> | [[IR-LED]]<br> | ||
| − | [[Reedkontact]] / Taster / | + | [[Reedkontact]] / Taster / Hall sensor [[HG1]]<br> |
Power 12 V = | Power 12 V = | ||
</td><tr></table> | </td><tr></table> | ||
Revision as of 22:41, 13 January 2018
Priorität rules VT VTL
VT-TINY VTL-Tiny
Usable for:
- Stop sign
- Priority control
- Construction sites
- Bottlenecks
- Parking stop / bus stop
- Priority control left turn VTL
The priority tiny can be used with DC-Car to control the traffic.
If a vehicle drives over a sensor (reed switch, Hall sensor HG1, IR sensor), an IR stop signal is generated for an adjustable time.
The stop signal of the VTL tiny only reacts to vehicles with the left turn signal switched on.
Partlist
|
to use with für 5 Volt |
expansion for 12 V |
Ready to work VTF und VFIRF ist not dem same as a kit!
Attention: FTR-+
www.DC-Car-Shop.eu
