Difference between revisions of "PC-Transmitter"
From wiki-en
m (→Allgemeines) |
m (→PC-Sender) |
||
| Line 1: | Line 1: | ||
[[File:dc-car2.jpg|400px|thumb|right|File:PC-Sender]] | [[File:dc-car2.jpg|400px|thumb|right|File:PC-Sender]] | ||
| − | ==PC- | + | ==PC-Transmitterr== |
| − | === | + | === General === |
| − | + | The IR emitters, 5 IR LED connected in series, can be installed on the ceiling. Thus, the vehicle can be reached almost everywhere. <br> | |
<br> | <br> | ||
| − | + | To use the [[PC Transmitter]], the vehicle must have a | have [[LCIR remote receiver]].<br> | |
| − | + | This requires, for example, the vehicle decoder [[: Category: DC07 | be DC07]] reported in which mode he is to receive. <br> | |
| − | + | see [: Category: DC-Car System | DC-Car System] Torrent | |
| − | + | e.g. CV21 = 24 for the DC-Car-PC transmitter with [[WinDigipet]] | |
<br> | <br> | ||
| − | === | + | === === Functions |
| − | + | Since WinDigipet Version 2009 is the system '' 'DC-CAR' '' set. <br> | |
<br> | <br> | ||
| − | + | This functions can be executed. Currently, 10 functions are possible. <br> | |
| − | * F0 | + | * F0 headlight |
| − | * F1 | + | * F1 Left indicator |
| − | * F2 | + | * F2 blinker law |
| − | * F3 | + | * F3 distance control from / to |
| − | * F4 | + | * F4 reed switch off / on |
| − | * F5 | + | * F5 blue light (4 blue lights on the roof) |
| − | * F6 Blitzer (1 | + | * F6 Blitzer (1 double Blitzer as grille) |
| − | * F7 | + | * F7 light 2 |
| − | * F8 | + | * F8 light 3 |
| − | * F9 | + | * F9 light 4 (if enabled via CV separated from light 3) |
<br> | <br> | ||
| − | === | + | === === Instructions |
| − | + | The indicator of the transmitter will only flash when functions are changed. <br> | |
| − | + | Therefore, different operation display on the PC and the condition of the vehicle after switching from one another! <br> | |
<br> | <br> | ||
| − | + | The range of the transmitter as the '' '[[DC-Car-Booster]]' '' a maximum of 7 meters. <br> | |
| − | + | It depends on the incorporation of [[remote receiver]] s in the model. Best is the reception on the passenger seat. <br> | |
| − | + | White plastic can be transparent to IR light. So from the outside, no change can be seen. <br> | |
| − | === | + | === === Manuals |
| − | [ | + | [Http://www.modellautobahnen.de/newsletter/Anleitungen/dc-car-pc-sender.pdf building instructions DC-Car-PC transmitter] |
<br> | <br> | ||
| − | === | + | === === Command Set |
| − | + | see [[instruction set]] | |
| − | === | + | === === SRCPD |
| − | + | The [[SRCPD]] is an open source project. | |
| − | === | + | === === Error |
| − | * | + | * The serial sections of the computer was incorrectly selected. Often there are 2 or more. |
| − | * | + | * For [[USB adapter]] or USB ports are the drivers missing or incorrectly installed. |
| − | & | + | & Nbsp; & Nbsp; In the operating system, the interface needs to be displayed. |
| − | * | + | * In the Software as [[WinDigipet]] must be installed interface under 16th |
| − | * | + | * The polarity of the power supply Note Minus = mass. |
| − | * | + | * Eighth case of several model railway [[transformer]] s to [[Synchronizing]]. |
| − | * | + | * The resistance for the IR-LED is designed for up to 5 IR LED in series. |
| − | * | + | * The voltage of 11-14 volts = enough for 4 IR LED 16-18 VOLT ~ enough for 5 IR-LED. |
| − | & | + | & Nbsp; & Nbsp; (There the rectifier has been replaced with a diode in order to reduce the heat generation) <br> |
| − | & | + | & Nbsp; & Nbsp; To test only one IR-LED can temporarily be used. <br> |
| − | * | + | * For the PC transmitter or DC-Car-Booster other IR LEDs are needed from the function module. |
| − | * | + | * Note: If an IR LED defect in the chain is no function possible. |
| − | & | + | & Nbsp; & Nbsp; By bridging a defective LED can be determined. <br> |
| − | + | Other errors See [[LCIR | LongControlIR]] | |
[[Category:DC-Car-System]] | [[Category:DC-Car-System]] | ||
[[Category:Software]] | [[Category:Software]] | ||
[[Category:Errorlist]] | [[Category:Errorlist]] | ||
Revision as of 08:39, 23 April 2016
PC-Transmitterr
General
The IR emitters, 5 IR LED connected in series, can be installed on the ceiling. Thus, the vehicle can be reached almost everywhere.
To use the PC Transmitter, the vehicle must have a | have LCIR remote receiver.
This requires, for example, the vehicle decoder be DC07 reported in which mode he is to receive.
see [: Category: DC-Car System | DC-Car System] Torrent
e.g. CV21 = 24 for the DC-Car-PC transmitter with WinDigipet
=== === Functions
Since WinDigipet Version 2009 is the system 'DC-CAR' set.
This functions can be executed. Currently, 10 functions are possible.
- F0 headlight
- F1 Left indicator
- F2 blinker law
- F3 distance control from / to
- F4 reed switch off / on
- F5 blue light (4 blue lights on the roof)
- F6 Blitzer (1 double Blitzer as grille)
- F7 light 2
- F8 light 3
- F9 light 4 (if enabled via CV separated from light 3)
=== === Instructions
The indicator of the transmitter will only flash when functions are changed.
Therefore, different operation display on the PC and the condition of the vehicle after switching from one another!
The range of the transmitter as the 'DC-Car-Booster' a maximum of 7 meters.
It depends on the incorporation of remote receiver s in the model. Best is the reception on the passenger seat.
White plastic can be transparent to IR light. So from the outside, no change can be seen.
=== === Manuals
building instructions DC-Car-PC transmitter
=== === Command Set see instruction set
=== === SRCPD The SRCPD is an open source project.
=== === Error
- The serial sections of the computer was incorrectly selected. Often there are 2 or more.
- For USB adapter or USB ports are the drivers missing or incorrectly installed.
& Nbsp; & Nbsp; In the operating system, the interface needs to be displayed.
- In the Software as WinDigipet must be installed interface under 16th
- The polarity of the power supply Note Minus = mass.
- Eighth case of several model railway transformer s to Synchronizing.
- The resistance for the IR-LED is designed for up to 5 IR LED in series.
- The voltage of 11-14 volts = enough for 4 IR LED 16-18 VOLT ~ enough for 5 IR-LED.
& Nbsp; & Nbsp; (There the rectifier has been replaced with a diode in order to reduce the heat generation)
& Nbsp; & Nbsp; To test only one IR-LED can temporarily be used.
- For the PC transmitter or DC-Car-Booster other IR LEDs are needed from the function module.
- Note: If an IR LED defect in the chain is no function possible.
& Nbsp; & Nbsp; By bridging a defective LED can be determined.
Other errors See LongControlIR
