Difference between revisions of "Function module"

Revision as of 08:48, 14 September 2023

Function modul

Light on / off

Function module

General

A function module transmits commands to a DC-Car decoder by means of a short range IR communication (10-20cm).
There are always 8 outputs available.
By using a dip switch 11 different module types are available
Supply voltage can be 12V - 16V AC or 12 - 16V DC
The outputs offer a current of 1A

By using a diode-circuit with 1N400x diodes it is possible to transmit multiple commands on one IR LED.

Stop module (All switches ON)

All switches ON Stop module means all 8 outputs sending a stop signal

Function Module A

Basic Commands
Dipswitch 1 must be set ON
1 = Speed at speed step 0 (stop)
2 = headlights 1 ON
3 = headlights 1 OFF
4 = Left indicator ON
5 = Right indicator ON
6 = Indicators OFF
7 = Speed at speed step 14
8 = Speed at speed step 28

Function Module B

Flashing Blue light vehicles
Dipswitch 2 must be set ON
1 = Speed at speed step 0 (stop)
2 = Hazard lights on
3 = Hazard kights OFF
4 = Flashing blue-light ON
5 = Flashing blue-light OFF
6 = Front-flasher ON
7 = Front-flasher OFF
8 = Speed at speed step 28

Function Module C

Additional lights and speed
Dipswitch 3 must be set ON

1 = Light 2 ON
2 = Light 2 OFF
3 = Light 3 ON
4 = Light 3 OFF
5 = Speed + 2 steps (accelerate)
6 = Speed - 2 steps (slowdown)
7 = Speed at speed step 10
8 = Speed at speed step 21

Function Module D

Automatic parking
Dip switch 4 must be set ON

(Stop time adjustable with CV108)
1 = Stop without direction indicators
2 = Stop with direction indicators on the left
3 = Stop with direction indicators on the right
4 = Stop with hazard lights
Drive off with driving position as specified in CV110 (flashing time adjustable with CV109)
5 = Driving / accelerating without direction indicators
6 = Drive / accelerate with direction indicators on the left
7 = Drive / accelerate with direction indicators on the right
8 = Driving / accelerating with hazard lights

Function Module E

Bus automatic
Dip switch 5 must be set ON

Commands E2 - E7 are only executed by vehicles that have
been configured as vehicle types 13, 14 or 15 in CV100!
1 = Speed at speed step 0 (Stop)
2 = Bus stop, direction indicators OFF, interior lighting OFF
3 = Bus stop, direction indicators OFF, interior lighting ON
4 = Bus stop, direction indicators right, interior lighting ON
5 = Bus stop, alarm light ON, interior lighting ON
(Flashing time adjustable in CV106)
6 = Bus leaves with speed step as set in CV105 and direction indicators left
7 = Arrival at the bus stop with speed step as set in CV102 and
direction indicators right (flashing time adjustable in CV101)
8 = Speed at speed step 0 (Stop)

Function Module F

Technic
Dip switch 6 on ON

1 = Switch OFF sensors front (FTR)
2 = Switch ON sensors front (FTR)
3 = Switch OFF reed contact
4 = Switch ON reed contact
5 = Switch OFF the light sensor
6 = Switch ON the light sensor
7 = Switch OFF rear IR LEDs
8 = Switch ON rear IR LEDs

Function Module G

Emergency vehicles
Dip switch 7 must be set ON

1 = Speed at speed step 0 (Stop)
2 = Rotating beacons and front flashers ON
3 = Rotating beacons and front flashers OFF
4 = Direction indicators left ON
5 = Direction indicators right ON
6 = Direction indicators OFF
7 = Speed in speed step 14
8 = Speed in speed step 28

Function Module H

Standard mix
Dipswitch 8 must be set ON

1 = Speed at speed step 0 (Stop)
2 = Light 1, direction indicators, flashing lights and front flasher OFF
3 = Light 1 ON
4 = Direction indicators left ON
5 = Direction indicators right ON
6 = Rotating beacons and front flashers ON
7 = Speed at speed step 14
8 = Speed at speed step 28

Function Module I

Remote control
All switches must be set OFF

1 = Time-controlled stop (programmed via CV108) direction indicator OFF
2 = Drive/accelerate after stop (time is out) with speed step from
CV110 (z.B. 1) direction indicator OFF
3 = Speed +2 (accelerate CV 98)
4 = All lights OFF
5 = Direction indicator left (with CV27=64 direction indicator
right + left (same time) = hazard lights possible)
6 = Direction indicator right (with CV27=64 direction
indicator right + left (same time) = hazard lights possible)
7 = Head light 1 (with CV60 light 1, 2, 3 and 4 at the same time possible)
8 = Beacon lights and front flashers with siren
(alternative: switch to continuous light for another two lights)

Function Module J

MF3, MF4 and MF5 functions (from 8.2016)
Dip switch 1 + 2 must be set ON

1 = Multi-function output (MF3) ON
2 = Multi-function output (MF3) OFF
3 = Multi-function output (MF4) ON
4 = Multi-function output (MF4) OFF
5 = Multi-function output (MF5) ON
6 = Multi-function output (MF5) OFF
7 = Speed at speed step 0 (Stop)
8 = Speed at speed step 0 (Stop)

Function module K

Anti collision system (from 3.2020)
Dip switch 1 + 3 must be set ON

1 = Speed at speed step 0 (Stop)
2 = Anti collision: Switch OFF rear IR LEDs
3 = Anti collision: Switch ON rear IR LEDs
4 = Direction indicators left ON
5 = Direction indicators right ON
6 = Direction indicators OFF
7 = Speed at speedstep 14
8 = Speed at speedstep 28

Function module L

Anti collision system (from 3.2020)
Dip switch 1 + 4 must be set ON

1 = Speed at speed step 0 (Stop)
2 = Headlights 1 ON
3 = Headlights 1 OFF
4 = Direction indicators left ON
5 = Direction indicators right ON
6 = Direction indicators OFF
7 = Anti collision: Switch OFF rear IR LEDs
8 = Anti collision: Switch ON rear IR LEDs

===Speedsteps M (dipswitch 1+5===
Dip switch 1 + 5 must be set ON. Available from version: 3.2020

1 = Speed at speed step 0 (Stop)
2 = Temporary stop
3 = Speedstep -2
4 = Speedstep +2
5 = Speed at speed step10
6 = Speed at speed step14
7 = Speed at speed step21
8 = Speed at speed step28

Parking N (dipswitch 1+6)

Dip switch 1 + 6 must be set ON. Available from version: 1.2020

1 = Speed at speed step 0 (Stop)
2 = Headlight 1 ON
3 = Headlight 1 OFF
4 = Temporary stop without hazard lights
5 = Temporary stop without hazard lights
6 = Temporary bus stop without hazard lights and interiour light
7 = Anti collision: Switch OFF rear IR LEDs
8 = Anti collision: Switch ON rear IR LEDs

Trailer I O (dipswitch 1+7)

Dip switch 1 + 7 must be set ON. Available from version: 1.2020

1 = Speed at speed step 0 (Stop)
2 = Headlight 1 ON
3 = Headlight 1 OFF
4 = Blue lights ON
5 = Front flasher ON
6 = Blue lights and front flasher OFF
7 = Anti collision: Switch OFF rear IR LEDs
8 = Anti collision: Switch ON rear IR LEDs

==Trailer II P (dipswitch 1+8)==
Dip switch 1 + 8 must be set ON. Available from version: 1.2020

1 = Speed at speed step 0 (Stop)
2 = Light 3 ON
3 = Light 3 OFF
4 = Blue lights ON
5 = Front flasher ON
6 = Blue lights and front flasher OFF
7 = Anti collision: rear IR OFF LEDs
8 = Anti collision: rear IR LEDs ON

Speed + direction indicators Q (dipswitch 2+3)

Dip switch 2 + 3 must be set ON. Available from version: 29. April 2020
(It may be necessary to replace the FB chip!)

1 = Speed at speed step 0 (Stop)
2 = Speed at speed step 10
3 = Speed at speed step 21
4 = Direction indicator left ON
5 = Direction indicator right ON
6 = Direction indicators OFF
7 = Speed at speed step 14
8 = Speed at speed step 28

Temporary stop R (dipswitch 2+4)

Dip switch 2 + 4 must be set ON. Available from version: 29. April 2020
(It may be necessary to replace the FB chip!)

1= Speed at speed step 0 (Stop)
2= Temporary stop CV108 Fahrzeug D1 indicators OFF
3= Temporary stop CV103 BUS E3 no indicators interiour light ON
4 = Direction indicator left ON
5 = Direction indicator right ON
6 = Direction indicators OFF
7 = Speed at speed step 14
8 = Speed at speed step 28

Blue lights and anti collision S (dipswitch 2+5)

Emergency vehicles Connection = command
Dip switch 2 + 5 must be set ON. Available from version: 25.6.2020

1 = Speed at speed step 0 (Stop)
2 = Temporary stop with hazard lights recommended CV108=0
3 = Depart with left indicator ON
4 = Blue lights ON
5 = Blue lights and front flasher OFF
6 = Frontflasher ON
7 = Anti collision: rear IR LEDs OFF
8 = Anti collision: rear IR LEDs ON

Lights and blue lights T (dipswitch 2+6)

Emergency vehicles Connection = command
Dip switch 2 + 5 must be set ON. Available from version: 25.6.2020

1 = Speed at speed step 0 (Stop)
2 = Headlight 1 ON
3 = Headlight 1 OFF
4 = Direction indicator left ON
5 = Direction indicator right ON
6 = Direction indicator OFF
7 = Direction indicator left ON
8 = Direction indicator left OFF

Automatic bus function Plus U(Schalter 2+7)

Busautomatik Connection = command
Dip switch 2 + 7 must be set ON. Available from version: 15.8.2020
Functions E2 - E7
Vehicle type 13, 14 or 15 in CV100!

1 = Speed at speed step 0 (Stop)
2 = Temporary bus stop, indicator OFF, interiour light OFF
3 = Temporary bus stop, indicator OFF, interiour light ON
4 = Temporary bus stop, right indicator ON, interiour light ON
5 = Temporary bus stop, hazard lights ON, interiour light ON
6 = Anti collision IR LEDs rear OFF
7 = Enter the bus stop with speed in CV102 and right direction indicator (flashing time in CV101)
8 = Anti collision IR LEDs rear ON

Automatic functions (dipswitch 2+8)

Dip switch 2 + 8 must be set ON. Available from decoder version: 11.2020

1 = Firebrigade 1st magnet
2 = Firebrigade 2e magnet
3 = Firebrigade column
4 = Bus 1st magnet
5 = Bus 2e magnet with hazard lights
6 = Bus departure
7 = Bus column
8 = Stop

Lane controll (dipswitch 3+4)

Dip switch 3 + 4 must be set ON. Available from version: june.2023

1 = Right lane (1)
2 = Middle lane (2)
3 = Left lane (4)
4 = Special lane (8)
5 = not used
6 = Lane controll (0) OFF
7 = DC-Car anti collision OFF
8 = DC-Car anti collision ON

Lights ON (dipswitch 3+5)

Dip switch 3 + 5 must be set ON. Available from version: 15.8.2021

1 = Speed at speed step 0 (Stop)
2 = Head lights ON
3 = Light 2 ON
4 = Light 3 ON
5 = Blue lights ON
6 = Front flasher ON
7 = Speed at speed step 14
8 = Speed at speed step 28

Special functions I (dipswitch 3+6)

Dip switch 3 + 6 must be set ON. Available from version: 3.2023

1 = Speed at speed step 0 (Stop)
2 = Speed at speed step 1
3 = Light 2 ON
4 = Light 2 OFF
5 = Light 3 ON
6 = Light 3 OFF
7 = Speed at speed step 10
8 = Speed at speed step 21

Special functions II (dipswitch 3+7)

Dip switch 3 + 7 must be set ON. Available from version: 1.12.2021

1 = Speed at speed step 0 (Stop)
2 = Temporary stop with indicators OFF
3 = Speed at speed step 21
4 = Direction indicators left ON
5 = Direction indicators right ON
6 = Direction indicators OFF
7 = Speed at speed step 14
8 = Speed at speed step 28

Driving backwards (3+8)

Dip switch 3 + 8 must be set ON. Available from version: 3.2023

1 = A1 Speed at speed step 0 (Stop)
2 = D1 Temporary stop with indicators OFF
3 = D4 Temporary stop with hazzard lights ON
4 = C6 Speed at speed step -2
5 = C7 Speed at speed step 10
6 = B6 Front flashers/sound ON
7 = B7 Front flashers/sound OFF
8 = A8 Speed at speed step 28

IR-LED on/in the street

Mounting of the IR-LED on the site:

The IR-LED is placed in or nearby the street in such a way that the cars can "see" the IR-light, emitted by the LED and execute the transmitted function at the intended place.
The IR-LED must be adjusted in a way, that the approaching vehicles can "see" it. On a straight line the vehicles detect the desired function in a distance of approx. 5 - 15cm from the LED
Sometimes a IR-LED influences the traffic on a parallel line too. In this case you can either increase the series resistor to decrease the range of the IR-signal or mount the LED into the street in a way that its IR beam lights vertical only. If you do the second, please use LED with a wider angle of reflection. Distance of the LEDs shoul be 5 - 10cm, but it is highly recommended to test it in every single case!

When the car passes the first LED it will start slowing down - an when it reaches the second LED in most cases it is that slow,
that it can come to a stop right there.
Using cars with a significiant lag it can be neccessary to use more LEDs

The LEDs are connected to the same connector, each ussing its own series resistor.

Remote control

Instead of function module I:
To make it easy for you we produce a battery powered remote control: MF plus.
The Plus version has build in test functions which can be used with the optional test set. These test functions have proved to be very usefull when building vehicles.
You can test polarity and working of LEDs as well measuring short circuits.
With the foto transistor (include in the set) your able to check the working of the IR LEDs at the back of the vehicles as well IR signals along the road.
And with the remote control it self your able to test the fototransistors at the front and the correct operation of the decoder and vehicle.

Function decoder

Function decoder

Using the function module in DCC mode with a digital center

A function module can be extended with a digital input. After extension the function module becomes a function decoder.
This enables switching the 8 outputs from a digital center using the addresses 1-8, (9-15), etc.
Note: All LEDs on each output are switched ON or OFF together! Especially in combination with other functions, like switching the light output makes sense.
The decoder can be used in the same way as the module, but offers the possibility to switch the 8 outputs separately by means of 8 digital addresses.

- central switching of "stop" for emergency OFF
- central switching of light for day-/night mode

Direction indicators are controlled by feedback sensors of junctions, lights are controlled by a digital addresses

Day/night control with a function decoder other functions still can be controlled by switches