|
|
(4 intermediate revisions by the same user not shown) |
Line 1: |
Line 1: |
− | [[File:xt_baustein.jpg|180px|thumb|XT-Baustein zur Montage unter der Platte]]
| |
− | ==Basics DC-Car-XT==
| |
− | '''Default: Evaluation of the battery test''' <br>
| |
− | <br>
| |
− | [[File: xt_dc08.png | 230px | thumb | Side reflector DC08 incl. Resistor]]
| |
− | * '''Sorting out vehicles with an empty battery to reach a charging station in conjunction with a software is fully automatic charging possible)'''
| |
− | Other options: see '''[[XT Modul]]'''
| |
− | [[File: xt_dc07.png | 230px | right | thumb | Side marker DC07 over 100 ohms resistance]]
| |
− | <br>
| |
− | [[File:xt_dc07.png|230px|right|thumb|Seitenstrahler DC07 über 100 Ohm Widerstand]]
| |
− | <br>
| |
| | | |
− | ==Infrared transmit and receive==
| |
− | The sensor requires a phototransistor. <br>
| |
− | It can be installed: <br>
| |
− | * In the guidepost
| |
− | * In the street as manhole cover
| |
− | * As a sensor in a stationary vehicle
| |
− | * hiding in trees, shrubs, buildings
| |
− | <br>
| |
− |
| |
− | ==Values for the car decoder==
| |
− | [[CV25]] = 1 Transmitting from the back (infrared LEDs of the rear distance control) <br>
| |
− | or CV25 = 4 Side or bottom transmitter <br>
| |
− | [[CV26]] Function of the vehicle with battery empty
| |
− | [[CV27]] = 2 or 10 battery test turned on
| |
− | [[CV28]] = 50 (1.2V) or 100 (2.4V) or 130 (3.6V battery)
| |
− |
| |
− | ==DC-Car-XT-Modul==
| |
− | [[File:xt_leitpfosten.png|230px|thumb|Leitpfosten mit FTR]]
| |
− | [[File:Xt sende ir1.png|230px|thumb|Montageort der Sendediode]]
| |
− | #Switching a 3-way servo turn out <br>
| |
− | # Switching a contact to ground / GND <br>
| |
− | #Transmitting a freely selectable DC Car Infrared command <br>
| |
− | <br>
| |
− | You can choose whether the respective function is resetted after a certain time or by triggering a reed contact. <br>
| |
− | === Pin assignment ===
| |
− | [[File:xt_anschluss.png|400px|Anschlussbeschreibung des XT-Modul]]
| |
− | === Connection Description ===
| |
− | DC voltage of 5V / 500mA via screw terminal block or the mini USB port. <br>
| |
− | * '''LED indicator''' <br>
| |
− | Green LED 5V operating voltage available. Blue LED received valid signal. <br>
| |
− | * '''Phototransistor (+ and -)''' <br>
| |
− | Note: Reverse marked as an LED. <br>
| |
− | * '''Servo connection''' <br>
| |
− | For direct control of a servo on the XT module.
| |
− | Please pay attention to the correct connection sequence, as these might vary with the different manufacturers. <br>
| |
− | === Setting XT module ===
| |
− | ...
| |
− |
| |
− | [[Category:Index_DE]]
| |
− | [[Category:Index_US]]
| |
− | [[Category:Index_UK]]
| |
− | [[Category:Trafficcontrol]]
| |
− | [[Category:XT_modul]]
| |
− | [[Category:CV-List]]
| |