S8-2020

From wiki-en
Revision as of 01:04, 17 June 2020 by Siegmund (Talk | contribs) (Created page with "right =Servodecoder= == General == The classic decoder with 8 servo outputs with 2 positions each for <br> Turnouts, branches, signals, barriers (wi...")

(diff) ← Older revision | Latest revision (diff) | Newer revision → (diff)
Jump to: navigation, search
S8-2020.jpg

Servodecoder

General

The classic decoder with 8 servo outputs with 2 positions each for
Turnouts, branches, signals, barriers (with luffing), gates, fairground models with servo drive, etc.

After activation, the servo is switched off. This avoids overloading and high power consumption.
Unlike most competing products, the S8 does not shut down all the servos at the same time, but individually.
This avoids a flutter of the servos due to small disturbances.

Important is also the Power ON switch-lock. Most servos can stay turned off at power ON.
This prevents uncontrolled movement when switching on. (Power dependent)
Only with the actuation the desired position is approached.

Connection

DC voltage    
+ (red) 12-16 volts =   Ground (black) -
or    
AC voltage    
Phase (yellow) 12-16 volts ~   Ground (brown)

The servo decoder is marked with

Ground / Minus - (brown for Märklin) away from the heat sink and
Phase / Plus + (yellow for Märklin) connected to the heat sink.
Observe uniform mass! see also transformer

Normally, DCC does not care about the assignment of the digital connection.

For Motorola (Märklin) the decoder must be set to Motorola and the digital connection
to be connected with the correct polarity at the bottom next to the 9-pole plug. 
Märklin (brown and red). A reverse polarity leads to no damage, but also to no function. Therefore, using different protocols can help to turn around.
The current is limited to 2 A For full load, a transformer of over 30 VA is required.

No power is consumed by the servo if the power off is activated.
Only by the movement a higher current flow is needed.
If no power off is used, make sure that the servos do not have to hold a large mechanical load.
With a right mechanism, a lock can be achieved without load.
Depending on the quality of the servo, there may be a humming or twitching. A servo that has left its position due to an interference pulse tries to correct this. Many servo overshoot and find the position no longer correct.
This leads to glitches in the other servos.
Therefore, the operating mode can only be used with good mechanics.

Format DCC oder Motorola

Die Servodecoder S8DCC/MOT können durch eine Lötbrücke auf das Motorolaformat (Märklin) umgestellt werden.
Dadurch ersetzen sie die Decoder K87.

Setting

The rashes of the servos are set once with a PC. The free Servo Programmer software can be downloaded her.
After that, the servos are only addressed via the point address
The addresses are set with a button. Note the grid:

Decoder Adress
1 1-8
2 9-16
3 17-24
4 25-32

etc.

Software

Für Neueinsteiger ist Windigopet zu empfehlen. Der Servodecoder die Servodecoder von DC-Car können ohne eine Digitalzentrale mit Windigipet am PC benutzt werden.

Das Nachrüsten von bestehenden Anlagen mit DC-Car-Servodecoder ist auch kein Problem.
In der Software wie Windigipet, Traincontroller, Railware, ITrain usw. werden die Servo wie Weichen behandelt.
Bei Austausch von Magnetartikeldecodern beachten: Der S8 braucht 8 aufeinander folgende Adressen.
Wenn der S4DCC-MOT benutzt wird, ist das ersetzten eines K87 einfacher.
Dann dürften keine Änderungen an der Software notwendig sein.

Sonderanwendung

Wenn an einem Servodecoder noch Anschlüße übrig sind können die auch für andere Zwecke benutzt werden.
Modelle mit 5 Volt Technik können für eine mit dem Programmer voreingestellt Zeit in Funktion gehen.
z.B. eine Schalter/Sensor kann ein Objekt starten, das nach 10 Sekunden wieder aus geht.

  • Antrieben z.B. Windräder, Wassermühlen, Kirmesmodelle mit Motorantrieb, Kräne mit Motor usw.
  • DC-Car-Fahrzeugdecoder in Standmodellen Licht, Blinker, Blaulicht, können voreingestellt werden und auch das Stopsignal aussenden.
  • Sound die Sound-Tinys können durch eine Weichenadresse für eine kurze Zeit ausgelöst werden.
  • Sound die Sound-Prozessoren können durch 3 Weichenadresse für bis zu 7 Töne abspeilen.
  • wird ein 5 Volt Relais angeschlossen, können damit auch höher Spannungen geschaltet werden.


Bauanleitung

Bauanleitung mit Platine ab 2012

Änderung:
Statt eines Gleichrichters wird eine Diode und eine Brücke verwendet.
Energieeinsparung, weniger Wärmeentwicklung bei 16 oder 18 Volt~ Trafos.
Handbuch